smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.16.5-200.fc42.x86_64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 870 QVO 4TB Serial Number: S5STNF0R614596K LU WWN Device Id: 5 002538 f41656ee4 Firmware Version: SVQ02B6Q User Capacity: 4 000 787 030 016 bytes [4,00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.5/5852 ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Sep 12 20:33:59 2025 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 320) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 099 099 010 - 4 9 Power_On_Hours -O--CK 094 094 000 - 25691 12 Power_Cycle_Count -O--CK 099 099 000 - 532 177 Wear_Leveling_Count PO--C- 094 094 000 - 57 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 099 099 010 - 4 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 099 099 010 - 4 187 Uncorrectable_Error_Cnt -O--CK 099 099 000 - 10 190 Airflow_Temperature_Cel -O--CK 075 020 000 - 25 195 ECC_Error_Rate -O-RC- 199 199 000 - 10 199 CRC_Error_Count -OSRCK 100 100 000 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 228 241 Total_LBAs_Written -O--CK 099 099 000 - 419829412810 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 10 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 10 [1] occurred at disk power-on lifetime: 4942 hours (205 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 01 d1 70 b8 78 40 00 Error: UNC 8 sectors at LBA = 0x1d170b878 = 7808792696 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 01 d1 70 b8 78 40 00 06:24:59.075 READ DMA EXT e1 00 00 00 0f 00 00 00 00 00 00 40 00 06:24:59.075 IDLE IMMEDIATE ef 00 03 00 46 00 00 00 00 00 00 40 00 06:24:59.075 SET FEATURES [Set transfer mode] ef 00 02 00 00 00 00 00 00 00 00 40 00 06:24:59.075 SET FEATURES [Enable write cache] ef 00 90 00 06 00 00 00 00 00 00 40 00 06:24:59.075 SET FEATURES [Disable SATA feature] Error 9 [0] occurred at disk power-on lifetime: 4942 hours (205 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 00 00 00 d1 70 b8 78 00 00 06:24:58.488 READ FPDMA QUEUED 60 00 08 00 00 00 00 d1 70 b8 70 00 00 06:24:58.488 READ FPDMA QUEUED 60 00 08 00 00 00 00 d1 70 b8 68 00 00 06:24:58.488 READ FPDMA QUEUED 60 00 08 00 00 00 00 d1 70 b8 60 00 00 06:24:58.488 READ FPDMA QUEUED 60 00 08 00 00 00 00 d1 70 b8 58 00 00 06:24:58.488 READ FPDMA QUEUED Error 8 [3] occurred at disk power-on lifetime: 4941 hours (205 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 00 00 01 d1 70 ba 00 40 00 Error: at LBA = 0x1d170ba00 = 7808793088 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 04 00 00 08 00 00 d1 70 b6 00 40 01 06:24:26.692 READ FPDMA QUEUED 60 04 00 00 00 00 00 d1 70 b2 00 40 00 06:24:26.692 READ FPDMA QUEUED 60 04 00 00 08 00 00 d1 70 ae 00 40 01 06:24:26.692 READ FPDMA QUEUED 60 04 00 00 00 00 00 d1 70 aa 00 40 00 06:24:26.692 READ FPDMA QUEUED 60 04 00 00 08 00 00 d1 70 a6 00 40 01 06:24:26.692 READ FPDMA QUEUED Error 7 [2] occurred at disk power-on lifetime: 4882 hours (203 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 01 d1 70 b8 78 40 00 Error: UNC 8 sectors at LBA = 0x1d170b878 = 7808792696 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 01 d1 70 b8 78 40 00 06:43:21.391 READ DMA EXT e1 00 00 00 0f 00 00 00 00 00 00 40 00 06:43:21.391 IDLE IMMEDIATE ef 00 03 00 46 00 00 00 00 00 00 40 00 06:43:21.391 SET FEATURES [Set transfer mode] ef 00 02 00 00 00 00 00 00 00 00 40 00 06:43:21.391 SET FEATURES [Enable write cache] ef 00 90 00 06 00 00 00 00 00 00 40 00 06:43:21.391 SET FEATURES [Disable SATA feature] SMART Error Log Version: 1 ATA Error Count: 10 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 10 occurred at disk power-on lifetime: 4942 hours (205 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 78 b8 70 40 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- e1 00 0f 00 00 00 40 00 06:24:59.075 IDLE IMMEDIATE ef 03 46 00 00 00 40 00 06:24:59.075 SET FEATURES [Set transfer mode] ef 02 00 00 00 00 40 00 06:24:59.075 SET FEATURES [Enable write cache] ef 90 06 00 00 00 40 00 06:24:59.075 SET FEATURES [Disable SATA feature] e1 00 02 00 00 00 40 00 06:24:59.075 IDLE IMMEDIATE Error 9 occurred at disk power-on lifetime: 4942 hours (205 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 00 51 01 10 00 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 00 78 b8 70 00 00 06:24:58.488 READ FPDMA QUEUED 60 08 00 70 b8 70 00 00 06:24:58.488 READ FPDMA QUEUED 60 08 00 68 b8 70 00 00 06:24:58.488 READ FPDMA QUEUED 60 08 00 60 b8 70 00 00 06:24:58.488 READ FPDMA QUEUED 60 08 00 58 b8 70 00 00 06:24:58.488 READ FPDMA QUEUED Error 8 occurred at disk power-on lifetime: 4941 hours (205 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 00 51 00 00 ba 70 40 Error: at LBA = 0x0070ba00 = 7387648 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 08 00 b6 70 40 01 06:24:26.692 READ FPDMA QUEUED 60 00 00 00 b2 70 40 00 06:24:26.692 READ FPDMA QUEUED 60 00 08 00 ae 70 40 01 06:24:26.692 READ FPDMA QUEUED 60 00 00 00 aa 70 40 00 06:24:26.692 READ FPDMA QUEUED 60 00 08 00 a6 70 40 01 06:24:26.692 READ FPDMA QUEUED Error 7 occurred at disk power-on lifetime: 4882 hours (203 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 78 b8 70 40 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- e1 00 0f 00 00 00 40 00 06:43:21.391 IDLE IMMEDIATE ef 03 46 00 00 00 40 00 06:43:21.391 SET FEATURES [Set transfer mode] ef 02 00 00 00 00 40 00 06:43:21.391 SET FEATURES [Enable write cache] ef 90 06 00 00 00 40 00 06:43:21.391 SET FEATURES [Disable SATA feature] e1 00 02 00 00 00 40 00 06:43:21.391 IDLE IMMEDIATE Error 6 occurred at disk power-on lifetime: 4882 hours (203 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 00 51 01 10 00 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 00 78 b8 70 00 00 06:43:20.800 READ FPDMA QUEUED 60 08 00 70 b8 70 00 00 06:43:20.800 READ FPDMA QUEUED 60 08 00 68 b8 70 00 00 06:43:20.800 READ FPDMA QUEUED 60 08 00 60 b8 70 00 00 06:43:20.800 READ FPDMA QUEUED 60 08 00 58 b8 70 00 00 06:43:20.800 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 256 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 25 Celsius Power Cycle Min/Max Temperature: 22/22 Celsius Lifetime Min/Max Temperature: 23/80 Celsius Specified Max Operating Temperature: 70 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (19) Index Estimated Time Temperature Celsius 20 2025-09-11 23:20 29 ********** ... ..( 44 skipped). .. ********** 65 2025-09-12 06:50 29 ********** 66 2025-09-12 07:00 48 ***************************** 67 2025-09-12 07:10 55 ************************************ 68 2025-09-12 07:20 57 ************************************** 69 2025-09-12 07:30 58 *************************************** 70 2025-09-12 07:40 59 **************************************** 71 2025-09-12 07:50 59 **************************************** 72 2025-09-12 08:00 60 ***************************************+ ... ..( 2 skipped). .. ***************************************+ 75 2025-09-12 08:30 60 ***************************************+ 76 2025-09-12 08:40 41 ********************** 77 2025-09-12 08:50 ? - ... ..( 12 skipped). .. - 90 2025-09-12 11:00 ? - 91 2025-09-12 11:10 28 ********* 92 2025-09-12 11:20 ? - 93 2025-09-12 11:30 35 **************** 94 2025-09-12 11:40 ? - ... ..( 6 skipped). .. - 101 2025-09-12 12:50 ? - 102 2025-09-12 13:00 38 ******************* 103 2025-09-12 13:10 50 ******************************* 104 2025-09-12 13:20 57 ************************************** 105 2025-09-12 13:30 57 ************************************** 106 2025-09-12 13:40 ? - 107 2025-09-12 13:50 53 ********************************** 108 2025-09-12 14:00 54 *********************************** 109 2025-09-12 14:10 55 ************************************ 110 2025-09-12 14:20 56 ************************************* 111 2025-09-12 14:30 56 ************************************* 112 2025-09-12 14:40 57 ************************************** 113 2025-09-12 14:50 57 ************************************** 114 2025-09-12 15:00 58 *************************************** ... ..( 8 skipped). .. *************************************** 123 2025-09-12 16:30 58 *************************************** 124 2025-09-12 16:40 59 **************************************** ... ..( 2 skipped). .. **************************************** 127 2025-09-12 17:10 59 **************************************** 0 2025-09-12 17:20 60 ***************************************+ ... ..( 3 skipped). .. ***************************************+ 4 2025-09-12 18:00 60 ***************************************+ 5 2025-09-12 18:10 59 **************************************** ... ..( 5 skipped). .. **************************************** 11 2025-09-12 19:10 59 **************************************** 12 2025-09-12 19:20 58 *************************************** 13 2025-09-12 19:30 59 **************************************** 14 2025-09-12 19:40 58 *************************************** 15 2025-09-12 19:50 59 **************************************** 16 2025-09-12 20:00 59 **************************************** 17 2025-09-12 20:10 53 ********************************** 18 2025-09-12 20:20 38 ******************* 19 2025-09-12 20:30 ? - SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 532 --- Lifetime Power-On Resets 0x01 0x010 4 25691 --- Power-on Hours 0x01 0x018 6 419829412810 --- Logical Sectors Written 0x01 0x020 6 2165750662 --- Number of Write Commands 0x01 0x028 6 2075337649246 --- Logical Sectors Read 0x01 0x030 6 7550517426 --- Number of Read Commands 0x01 0x038 6 2264000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 10 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 79 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 25 --- Current Temperature 0x05 0x020 1 80 --- Highest Temperature 0x05 0x028 1 23 --- Lowest Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 1747 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 6 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC